Controlling Selenization Equilibrium Enables High-Quality Kesterite Absorbers for Efficient Solar Cells.

Kesterite Cu2ZnSn(S, Se)4 is considered one of the most competitive photovoltaic materials due to its earth-abundant and nontoxic constituent elements, environmental friendliness, and high stability. However, the preparation of high-quality Kesterite absorbers for photovoltaics is still challenging for the uncontrollability and complexity of selenization reactions between metal element precursors and selenium. In this study, we propose a solid-liquid/solid-gas (solid precursor and liquid/vapor Se) synergistic reaction strategy to precisely control the selenization process. By pre-depositing excess liquid selenium, we provide the high chemical potential of selenium to facilitate the direct and rapid formation of the Kesterite phase. The further optimization of selenium condensation and subsequent volatilization enables the efficient removal of organic compounds and thus improves charge transport in the absorber film. As a result, we achieve high-performance Kesterite solar cells with total-area efficiency of 13.6% (certified at 13.44%) and 1.09 cm2-area efficiency of 12.0% (certified at 12.1%).

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF.

Increasing the fill factor (FF) and the open-circuit voltage (VOC ) simultaneously together with non-decreased short-circuit current density (JSC ) are a challenge for highly efficient Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells. Aimed at such target in CZTSSe solar cells, a synergistic strategy to tailor the recombination in the bulk and at the heterojunction interface has been developed, consisting of atomic-layer deposited aluminum oxide (ALD-Al2 O3 ) and (NH4 )2 S treatment. With this strategy, deep-level CuZn defects are converted into shallower VCu defects and improved crystallinity, while the surface of the absorber is optimized by removing Zn- and Sn-related impurities and incorporating S. Consequently, the defects responsible for recombination in the bulk and at the heterojunction interface are effectively passivated, thereby prolonging the minority carrier lifetime and increasing the depletion region width, which promote carrier collection and reduce charge loss. As a consequence, the VOC deficit decreases from 0.607 to 0.547 V, and the average FF increases from 64.2% to 69.7%, especially, JSC does not decrease. Thus, the CZTSSe solar cell with the remarkable efficiency of 13.0% is fabricated. This study highlights the increased FF together with VOC simultaneously to promote the efficiency of CZTSSe solar cells, which could also be applied to other photoelectronic devices.

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells.

Vapor-transport deposition (VTD) method is the main technique for the preparation of Sb2Se3 films. However, oxygen is often present in the vacuum tube in such a vacuum deposition process, and Sb2O3 is formed on the surface of Sb2Se3 because the bonding of Sb-O is formed more easily than that of Sb-Se. In this work, the formation of Sb2O3 and thus the carrier transport in the corresponding solar cells were studied by tailoring the deposition microenvironment in the vacuum tube during Sb2Se3 film deposition. Combined by different characterization techniques, we found that tailoring the deposition microenvironment can not only effectively inhibit the formation of Sb2O3 at the CdS/Sb2Se3 interface but also enhance the crystalline quality of the Sb2Se3 thin film. In particular, such modification induces the formation of (hkl, l = 1)-oriented Sb2Se3 thin films, reducing the interface recombination of the subsequently fabricated devices. Finally, the Sb2Se3 solar cell with the configuration of ITO/CdS/Sb2Se3/Spiro-OMeTAD/Au achieves a champion efficiency of 7.27%, a high record for Sb2Se3 solar cells prepared by the VTD method. This work offers guidance for the preparation of high-efficiency Sb2Se3 thin-film solar cells under rough-vacuum conditions.

Ge Bidirectional Diffusion to Simultaneously Engineer Back Interface and Bulk Defects in the Absorber for Efficient CZTSSe Solar Cells.

Aiming at a large open-circuit voltage (VOC ) deficit in Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells, a new and effective strategy to simultaneously regulate the back interface and restrain bulk defects of CZTSSe absorbers is developed by directly introducing a thin GeO2 layer on Mo substrates. Power conversion efficiency (power-to-efficiency) as high as 13.14% with a VOC of 547 mV is achieved for the champion device, which presents a certified efficiency of 12.8% (aperture area: 0.25667 cm2 ). Further investigation reveals that Ge bidirectional diffusion simultaneously occurs toward the CZTSSe absorber and MoSe2 layer at the back interface while being selenized. That is, some Ge element from the GeO2 diffuses into the CZTSSe absorber layer to afford Ge-doped absorbers, which can significantly reduce the defect density and band tailing, and facilitate quasi-Fermi level split by relatively higher hole concentration. Meanwhile, a small amount of Ge element also participates in the formation of MoSe2 at the back interface, thus enhancing the work function of MoSe2 and effectively separating photoinduced carriers. This work highlights the synergistic effect of Ge element toward the bulk absorber and the back interface and also provides an easy-handling way to achieve high-performance CZTSSe solar cells.

Two-Step Annealing CZTSSe/CdS Heterojunction to Improve Interface Properties of Kesterite Solar Cells.

The post-heating treatment of the CZTSSe/CdS heterojunction can enhance the interfacial properties of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. In this regard, a two-step annealing method was developed to enhance the heterojunction quality for the first time. That is, a low-temperature (90 °C) process was introduced before the high-temperature treatment, and 12.3% efficiency of CZTSSe solar cells was achieved. Further investigation revealed that the CZTSSe/CdS heterojunction band alignment with a smaller spike barrier can be realized by the two-step annealing treatment, which assisted in carrier transportation and reduced the charge recombination loss, thus enhancing the open-circuit voltage (VOC) and fill factor (FF) of the devices. In addition, the two-step annealing could effectively avoid the disadvantages of direct high-temperature treatment (such as more pinholes on CdS films and excess element diffusion), improve the CdS crystallization, and decrease the defect densities within the device, especially interfacial defects. This work provides an effective method to improve the CZTSSe/CdS heterojunction properties for efficient kesterite solar cells.